| ABEC AND ISO STANDARDS |
| Precision ball bearings are manufactured to standards established by the Annular Bearing Engineers Committee (ABEC) of the American Bearing Manufacturers Association (ABMA). These standards have been accepted by the American National Standards Institute (ANSI) and conform essentially to the standards set by the International Standards Organization (ISO). |
IMPORTANT NOTE: |
The ABEC and ISO bearing standards are primarily concerned with bearing tolerances. While tolerance is an important factor in the performance of a bearing, there are many other factors that also affect the suitability of a bearing to its application. ABEC and ISO standards do not cover: radial play, raceway curvature, surface finish, material, ball complement, number, size or precision level, retainer type, lubrication, torque, cleanliness at assembly, packaging and other factors that may be essential to the desired bearing performance. |
|
| The tolerances shown in the ABEC and ISO tables are specific for basic bearing dimensions and require no further explanation. The following information may also help the design engineer use the runout values shown for different tolerance ratings. |
RADIAL RUNOUT
Outer ring: The total indicator reading during one complete revolution of the outer ring with the inner ring remaining stationary.
Inner ring: The total indicator reading during one complete revolution of the inner ring with the outer ring remaining stationary. |
 |
FACE RUNOUT
Inner ring: The total indicator reading during one complete revolution of the inner ring with the outer ring remaining stationary.
Outer ring: The total indicator reading during one complete revolution of the outer ring with the inner ring remaining stationary. |
 |
FACE RUNOUT WITH BORE
The total indicator reading during one complete revolution of the inner ring. |
 |
O.D. RUNOUT WITH FACE
The total indicator reading during one complete revolution of the outer ring. The outer ring is positioned against 2 stops oriented at 90° to each other. |
 |
| ABEC/ISO TOLERANCE CHART Dimensions in Inches (mm) |
INNER RING TOLERANCES Inches (mm) |
|
TYPE |
OD SIZE |
ABEC 1
ISO Normal |
ABEC 3
ISO P6 |
ABEC 5
ISO P5 |
ABEC 7
ISO P4 |
MEAN BORE TOLERANCE |
ALL |
0 to .709
0 to 18 |
0 to -.0003
0 to -.008 |
0 to -.0002
0 to -.005 |
0 to -.0002
0 to -.005 |
0 to -.0002
0 to -.005 |
2 PT OUT OF ROUNDNESS* |
ALL |
0 to .709
0 to 18 |
NS |
NS |
.0001
.003 |
.0001
.003 |
BORE TAPER* |
ALL |
0 to .709
0 to 18 |
NS |
NS |
.0001
.003 |
.0001
.003 |
RADIAL RUNOUT* |
ALL |
0 to .709
0 to 18 |
.0003
.008 |
.0002
.005 |
.00015
.004 |
.0001
.003 |
FACE RUNOUT WITH BORE* |
ALL |
0 to .709
0 to 18 |
NS |
NS |
.0003
.008 |
.0001
.003 |
FACE RUNOUT* |
ALL |
0 to .709
0 to 18 |
NS |
NS |
.0003
.008 |
.0001
.003 |
WIDTH VARIATION* |
ALL |
0 to .709
0 to 18 |
NS |
NS |
.0002
.005 |
.0001
.003 |
RING WIDTH TOLERANCE |
ALL |
0 to 1.1811
0 to 30 |
0 to -.005
0 to -.125 |
0 to -.005
0 to -.125 |
0 to -.001
0 to -.025 |
0 to -.001
0 to -.025 |
|
| * Maximum allowed value NS = Not Specified |
